It seems that if you set the packet mark on a packet and then route
that packet through a kernel VXLAN interface, the VXLAN-encapsulated
packet will still have the mark from the original packet. Since our
NAT rules are based on the packet mark, this was causing us to
double-NAT some packets, which then triggered a kernel checksumming
bug. But even without the checksum bug, there are reasons to avoid
double-NATting, so fix the rules to unmark the packets before
masquerading them.
Fixes two small issues with the metric added in #90175:
1. Bump the timestamp on initial informer sync. Otherwise it remains 0 if
restarting kube-proxy in a quiescent cluster, which isn't quite right.
2. Bump the timestamp even if no healthz server is specified.
This adds a metric, kubeproxy_sync_proxy_rules_last_queued_timestamp,
that captures the last time a change was queued to be applied to the
proxy. This matches the healthz logic, which fails if a pending change
is stale.
This allows us to write alerts that mirror healthz.
Signed-off-by: Casey Callendrello <cdc@redhat.com>
This builds on previous work but only sets the sysctlConnReuse value
if the kernel is known to be above 4.19. To avoid calling GetKernelVersion
twice, I store the value from the CanUseIPVS method and then check the version
constraint at time of expected sysctl call.
Signed-off-by: Christopher M. Luciano <cmluciano@us.ibm.com>
This allows the proxier to cache local addresses instead of fetching all
local addresses every time in IsLocalIP.
Signed-off-by: Andrew Sy Kim <kiman@vmware.com>
This creates a new EndpointSliceProxying feature gate to cover EndpointSlice
consumption (kube-proxy) and allow the existing EndpointSlice feature gate to
focus on EndpointSlice production only. Along with that addition, this enables
the EndpointSlice feature gate by default, now only affecting the controller.
The rationale here is that it's really difficult to guarantee all EndpointSlices
are created in a cluster upgrade process before kube-proxy attempts to consume
them. Although masters are generally upgraded before nodes, and in most cases,
the controller would have enough time to create EndpointSlices before a new node
with kube-proxy spun up, there are plenty of edge cases where that might not be
the case. The primary limitation on EndpointSlice creation is the API rate limit
of 20QPS. In clusters with a lot of endpoints and/or with a lot of other API
requests, it could be difficult to create all the EndpointSlices before a new
node with kube-proxy targeting EndpointSlices spun up.
Separating this into 2 feature gates allows for a more gradual rollout with the
EndpointSlice controller being enabled by default in 1.18, and EndpointSlices
for kube-proxy being enabled by default in the next release.
This includes IPv4 and IPv6 address types and IPVS dual stack support.
Importantly this ensures that EndpointSlices with a FQDN address type
are not processed by kube-proxy.
The proxy healthz server assumed that kube-proxy would regularly call
UpdateTimestamp() even when nothing changed, but that's no longer
true. Fix it to only report unhealthiness when updates have been
received from the apiserver but not promptly pushed out to
iptables/ipvs.
Kube-proxy runs two different health servers; one for monitoring the
health of kube-proxy itself, and one for monitoring the health of
specific services. Rename them to "ProxierHealthServer" and
"ServiceHealthServer" to make this clearer, and do a bit of API
cleanup too.
The detectStaleConnections function in kube-proxy is very expensive in
terms of CPU utilization. The results of this function are only actually
used for UDP ports. This adds a protocol attribute to ServicePortName to
make it simple to only run this function for UDP connections. For
clusters with primarily TCP connections this can improve kube-proxy
performance by 2x.
This should fix a bug that could break masters when the EndpointSlice
feature gate was enabled. This was all tied to how the apiserver creates
and manages it's own services and endpoints (or in this case endpoint
slices). Consumers of endpoint slices also need to know about the
corresponding service. Previously we were trying to set an owner
reference here for this purpose, but that came with potential downsides
and increased complexity. This commit changes behavior of the apiserver
endpointslice integration to set the service name label instead of owner
references, and simplifies consumer logic to reference that (both are
set by the EndpointSlice controller).
Additionally, this should fix a bug with the EndpointSlice GenerateName
value that had previously been set with a "." as a suffix.
Work around Linux kernel bug that sometimes causes multiple flows to
get mapped to the same IP:PORT and consequently some suffer packet
drops.
Also made the same update in kubelet.
Also added cross-pointers between the two bodies of code, in comments.
Some day we should eliminate the duplicate code. But today is not
that day.
Kube-proxy will add ipset entries for all node ips for an SCTP nodeport service. This will solve the problem 'SCTP nodeport service is not working for all IPs present in the node when ipvs is enabled. It is working only for node's InternalIP.'
As mentioned in issue #80061, in iptables lock contention case,
we can see increasing rate of iptables restore failures because it
need to grab iptables file lock.
The failure metric can provide administrators more insight
Metrics will be collected in kube-proxy iptables and ipvs modes
Signed-off-by: Hui Luo <luoh@vmware.com>
ipvs `getProxyMode` test fails on mac as `utilipvs.GetRequiredIPVSMods`
try to reach `/proc/sys/kernel/osrelease` to find version of the running
linux kernel. Linux kernel version is used to determine the list of required
kernel modules for ipvs.
Logic to determine kernel version is moved to GetKernelVersion
method in LinuxKernelHandler which implements ipvs.KernelHandler.
Mock KernelHandler is used in the test cases.
Read and parse file is converted to go function instead of execing cut.
Computing all node ips twice would always happen when no node port
addresses were explicitly set. The GetNodeAddresses call would return
two zero cidrs (ipv4 and ipv6) and we would then retrieve all node IPs
twice because the loop wouldn't break after the first time.
Also, it is possible for the user to set explicit node port addresses
including both a zero and a non-zero cidr, but this wouldn't make sense
for nodeIPs since the zero cidr would already cause nodeIPs to include
all IPs on the node.
Previously the same ip addresses would be computed for each nodePort
service and this could be CPU intensive for a large number of nodePort
services with a large number of ipaddresses on the node.
Currently the BaseServiceInfo struct implements the ServicePort interface, but
only uses that interface sometimes. All the elements of BaseServiceInfo are exported
and sometimes the interface is used to access them and othertimes not
I extended the ServicePort interface so that all relevent values can be accessed through
it and unexported all the elements of BaseServiceInfo
This adds some useful metrics around pending changes and last successful
sync time.
The goal is for administrators to be able to alert on proxies that, for
whatever reason, are quite stale.
Signed-off-by: Casey Callendrello <cdc@redhat.com>
As part of the endpoint creation process when going from 0 -> 1 conntrack entries
are cleared. This is to prevent an existing conntrack entry from preventing traffic
to the service. Currently the system ignores the existance of the services external IP
addresses, which exposes that errant behavior
This adds the externalIP addresses of udp services to the list of conntrack entries that
get cleared. Allowing traffic to flow
Signed-off-by: Jacob Tanenbaum <jtanenba@redhat.com>
The current logic is to delete a RS if the number of active connections
is 0. This makes sense for TCP but for UDP the number of active
connections is always 0. This is an issue for DNS queries because the RS
will be deleted but the IPVS connection will remain until it expires
(5mn by default) and if there are a lot of DNS queries, the port will be
reused and queries blackholed. Of course for this to work properly the
service needs to continue to serve queries until the connections expire
(this works fine with the lameduck option of coredns).
- Move from the old github.com/golang/glog to k8s.io/klog
- klog as explicit InitFlags() so we add them as necessary
- we update the other repositories that we vendor that made a similar
change from glog to klog
* github.com/kubernetes/repo-infra
* k8s.io/gengo/
* k8s.io/kube-openapi/
* github.com/google/cadvisor
- Entirely remove all references to glog
- Fix some tests by explicit InitFlags in their init() methods
Change-Id: I92db545ff36fcec83afe98f550c9e630098b3135
while cleaning up ipvs mode. flushing iptable chains first and then
remove the chains. this avoids trying to remove chains that are still
referenced by rules in other chains.
fixes#70615
