The ziomon_fcpconf saves a lot of information about adapter into .cfg file.
With this patch ziorep_config tool will extract PCHID additional adapter
parameter from .cfg file and put it into .config file for future evaluation by
ziorep_* tools group.
This patch also adds notification for cases, when chid sysfs entry does not
exist for specified CHPID, for example for old kernels.
Before patch application typical line example from .config file looked like:
... 253:0 /dev/sde 8388672 8:64 Disk
After application of the patch typical line example from .config file
looks like:
... 253:0 /dev/sde 8388672 8:64 Disk 01c0
On older distros, which do not contain pchid sysfs entry, typical line
example from .config file looks like:
... 253:0 /dev/sde 8388672 8:64 Disk n/a
As PCHID value of FCP adapter can now be extracted from .config file,
add PCHID field to report of ziorep_config tool.
If there was no PCHID sysfs entry on the system, print following message into
ziorep_config command output:
...
PCHID: there is no PCHID entry in data source
...
Signed-off-by: Fedor Loshakov <loshakov@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Sakshi Singh <005c7w@linux.ibm.com>
Reviewed-by: M Nikhil <nikh1092@linux.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Perl logs warning message if a variable is not initialized.
get_device_data() set mp_dev with multipath device for a scsi disk device.
mp_dev remain uninitialized if there is no multipath device.
This can happen if a scsi device is not managed by dm multipath driver.
Warning message:
"Use of uninitialized value in subroutine entry at /usr/sbin/ziorep_config line 136"
Fix it by skipping the code dealing with mp_dev and continue with next
scsi device in the loop.
To reproduce, remove a scsi device from dm multipath.
$multipathd -k'del path sdh'
Then run `ziorep_config -D`.
Signed-off-by: Nihar Panda <niharp@linux.ibm.com>
Reviewed-by: Fedor Loshakov <loshakov@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
If system configuration contains zfcp-attached SCSI devices of Peripheral
Device Type disk, but without block device, e.g. because the storage reports
Peripheral Qualifier 1 in INQUIRY, ziorep_config tool issue the
following type of errors during generation of .config file from .cfg
file:
$ ziorep_config -I -i test.cfg
Unpacking configuration ...Done.
Use of uninitialized value in subroutine entry at /usr/sbin/ziorep_config line 36.
Use of uninitialized value in subroutine entry at /usr/sbin/ziorep_config line 36.
Use of uninitialized value in subroutine entry at /usr/sbin/ziorep_config line 54.
Use of uninitialized value in subroutine entry at /usr/sbin/ziorep_config line 135.
...
Such errors can also be seen during printing of adapter, device and map
reports:
$ ziorep_config -ADM -i test.cfg
Unpacking configuration ...Done.
Use of uninitialized value in subroutine entry at /usr/sbin/ziorep_config line 36.
Use of uninitialized value in subroutine entry at /usr/sbin/ziorep_config line 36.
Use of uninitialized value in subroutine entry at /usr/sbin/ziorep_config line 54.
Use of uninitialized value in subroutine entry at /usr/sbin/ziorep_config line 135.
...
This is because ziorep_config reads block device parameters from
non-existent block device subdirectory. And therefore ziorep_config
leaves block device major:minor number column empty in .config file
instead of filling it with 0:0 preset value afterwards.
As a consequence, ziorep_traffic tool, which is using .config file to
get information about devices, reports the following error:
$ ziorep_traffic test
Extracting config data...done
ziorep_traffic: Could not parse line 1 - configuration file broken?
To fix this, skip reading the block device parameters for such
devices, and use the preset values that have been set before
instead.
Signed-off-by: Fedor Loshakov <loshakov@linux.ibm.com>
Suggested-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
The value of "generic/dev" exists and can be retrieved directly under
the SCSI device directory, not under the disk block device subdirectory,
where the global variable $c_src points to after
$c_src = $devices{$hctl}{dev}; command.
So move the sg_mm retrieval before the block device parameters
retrieval.
Signed-off-by: Fedor Loshakov <loshakov@linux.ibm.com>
Suggested-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
This commit is based on the s390-tools-1.39.0 version.
Changes on top of s390-tools-1.39.0:
- Add MIT license to all source files
- Add LICENSE file
- Transform REAMDE to README.md (markdown)
- Add AUTHORS.md file
- Add CONTRIBUTING.md file
- Move changelog from README to CHANGELOG.md file
Reviewed-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Fedor Loshakov